cisco 300-615 practice test

Troubleshooting Cisco Data Center Infrastructure (DCIT)


Question 1 Topic 5

Topic 5

Refer to the exhibit. A network engineer is troubleshooting a Cisco Nexus 5000 Series Switch. The interface between the
server and the switch is nonoperational and is expected to operate at 10 Gbps. The drain rate of the interface is 3 Mbps.
Which action resolves the issue?

  • A. Configure pause error-disable recovery
  • B. Enable link level pause on the interface
  • C. Reset priority flow counters
  • D. Set priority flow control pause
Answer:

A

Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/troubleshooting/guide/
N5K_Troubleshooting_Guide/n5K_ts_fcoe.html

Discussions

Question 2 Topic 5

Topic 5

Refer to the exhibit. A functioning trunk port Ethernet1/48 exists between two identical Cisco Nexus 5000 Series Switches.
The interfaces on the switches support the MACsec feature and are configured identically. To enable manual MACsec, an
engineer adds the configuration shown in the exhibit to both sides of the trunk. The trunk port stops functioning. Which action
should be taken to resolve the issue?

  • A. Disable and then enable the port
  • B. Enable the license for the trunk ports to support MACsec
  • C. Lower the MTU value to less than 9216 bytes
  • D. Configure the PMK with a length of 2048 bytes
Answer:

B

Discussions

Question 3 Topic 5

Topic 5

Refer to the exhibit. An engineer cannot log in to the Cisco IMC page of the Cisco UCS C220 server. Which action resolves
the issue?

  • A. Use the FQDN of the Cisco IMC webpage login page instead of the IP address for the connection to be secure.
  • B. Replace the self-signed certificate that is installed on the Cisco IMC with a user certificate that is signed from the client corporate certificate authority.
  • C. Use the DNS of the Cisco IMC webpage login page instead of the IP address for the connection to be secure.
  • D. Replace the self-signed certificate that is installed on the Cisco IMC with a server certificate that is signed from the client corporate certificate.
Answer:

D

Discussions

Question 4 Topic 5

Topic 5

Refer to the exhibit. An upgrade operation fails with an error displayed. Which action resolves the issue?

  • A. Use a different system image.
  • B. Allocate extra space on a flash drive to extract a system image.
  • C. Use a different kickstart image.
  • D. Allocate extra space on a flash drive to extract a kickstart image.
Answer:

A

Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus1000/
sw/4_2_1_s_v_1_4_a/troubleshooting/configuration/guide/n1000v_trouble/ n1000v_trouble_5upgrade.html

Discussions

Question 5 Topic 5

Topic 5

Refer to the exhibit. During implementation of a Cisco UCS C-Series Server, an engineer receives the status that is shown in
the exhibit. Which action resolves the issue?

  • A. Insert an SD card into SLOT-2.
  • B. Reconfigure the Drive Type from “Removable” to “Non-Removable”.
  • C. Set SLOT-1 Sync Mode to “Auto”.
  • D. Configure the RAID that is associated with the card.
Answer:

C

Discussions

Question 6 Topic 5

Topic 5
An engineer enables the packet postcards feature on a Cisco Nexus 9000 Series Switch but receives this error message:
Error: Cannot configure postcard when inband-telemetry is configured.
Which action resolves the issue?

  • A. Disable the hardware-telemetry feature.
  • B. Disable the telemetry feature.
  • C. Disable the software-telemetry feature.
  • D. Disable the inband-telemetry feature.
Answer:

A

Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/92x/ programmability/guide/b-cisco-
nexus-9000-series-nx-os-programmability-guide-92x/b-cisconexus-9000-series-nx-os-programmability-guide-
92x_chapter_0100001.html

Discussions

Question 7 Topic 5

Topic 5
After upgrading a clients fabric interconnect to the latest version, an engineer discovers that the appliance has lost its entire
configuration. Which two locations should an engineer check to confirm that the appliance had backed up the configuration
prior to the upgrade in order to retrieve the lost configuration? (Choose two.)

  • A. Equipment FSM page, InternalBackup stage
  • B. Service profiles page, InternalBackup stage
  • C. Admin page, PollInternalBackup stage
  • D. Equipment FSM page, PollInternalBackup stage
  • E. Admin page, InternalBackup stage.
Answer:

A C

Discussions

Question 8 Topic 5

Topic 5

Refer to an exhibit. An engineer is troubleshooting an upgrade failure on a switch. Which action resolves the issue?

  • A. Save the system image in NVRAM.
  • B. Use the same system image as the kickstart image.
  • C. Load a new system image.
  • D. Reload the same system image.
Answer:

C

Discussions

Question 9 Topic 5

Topic 5
An IOM fails during a firmware upgrade and is unresponsive. Which action recovers the module?

  • A. Restore the Cisco UCS Manager configuration from backup.
  • B. Roll back to the previous firmware.
  • C. Reinstall the firmware using Auto Install.
  • D. Reset the faulty module from the peer IOM.
Answer:

B

Discussions

Question 10 Topic 5

Topic 5

Refer to the exhibit. Cisco UCS Manager is upgraded using the Auto Install feature, but the FSM fails. Which action resolves
the issue?

  • A. Acknowledge the primary fabric interconnect.
  • B. Remove the service pack from the subordinate fabric interconnect.
  • C. Clear the startup version of the default infrastructure pack.
  • D. Use the force option to upgrade the infrastructure firmware.
Answer:

C

Discussions
To page 2